The Basics of Plumbing Knowledge When Installing a Bathtub
The Basics of Plumbing Knowledge When Installing a Bathtub
Blog Article
This article following next on the subject of Installing A Bathtub is unquestionably attention-grabbing. Read it yourself and figure out what you think about it.
Setting up a bathtub isn't precisely rocket science, however it does require solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is likewise a moderately tough job. If the old tub is conveniently easily accessible, the task can move quickly; if you need to open up a wall surface to remove the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make sure you have qualified yourself for the task and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will assist you install a new tub in your washroom if you have actually currently gotten a brand-new bathtub and don't need to transform the arrangement of your previous water pipes.
Your devices and material checklist ought to consist of the following:
Planning for the Setup
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the limited accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the bath tub in the called for setting. The wood boards are useful in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bath tub up until the spirit level checks out degree.
To install taps, fit all-time low of the furthest adaptable faucet port to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water and inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally examine the overflow electrical outlet and also the normal outlet for leakages.
Lastly, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub needs to wait up until the bathtub has been used at the very least once as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washers remain in location in between the tap and the sink. Secure the tap in position with the producer given backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break a rigid seal, triggering the water to pass through the wall surface between the bath and the tiling, resulting in problems with moisture as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealant can crack relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently available on the market. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very inquisitive about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed reading my piece. So long as you enjoyed reading our blog post kindly make sure you remember to share it. Thanks a lot for going through it.
Expert plumbing solutions, one click. Report this page